Skip to content
  • Reptile Dragon 2 Discord
  • FPV Slovakia Discord
  • ROTOR BUILDS
wizzx.tech

wizzx.tech

FPV world by WizzX

  • Home
  • WizzX 3D models
  • About me
    • Contact Form
  • Home
  • WizzX 3D models
  • About me
    • Contact Form

Author: WizzX

WizzX’s 3D models download and purchase on my web page
3D Print / arduino / download / RC | FPV

WizzX’s 3D models download and purchase on my web page

June 10, 2022June 10, 20220

Some years ago I started with my own design of 3d printed parts for drones an planes.As it is much better to find correct place for components in 3D mode …

FLOWBOX starting guide
FLOWBOX / Gyroflow / INAV Betaflight / RC | FPV

FLOWBOX starting guide

August 5, 2021September 8, 20215

This is an initial setup guide for FlowBox – really nice IMU board used for video stabilization 1. Download / install Betaflight configurator 10.8.0 (nightlies) https://github.com/betaflight/betaflight-configurator-nightlies/releases/ 2. Update firmware – …

SPARTAN RACE
MISC

SPARTAN RACE

August 4, 2021August 4, 20210

This article is totally of topic of this technical site, but why not? Few years I just admire how interesting is run, get dirty and be strong at the same …

ZMReborn 230 (ZMR250 in 2021) 3PV
3D Print / ZMR250

ZMReborn 230 (ZMR250 in 2021) 3PV

June 16, 2021June 16, 20210

ZMReborn or ZMR250@230 3PV rigSo, this is my 4th modification of still living ZMR250 frame (as I still have many spare carbon parts) where Im using 3D printed spacers between …

Radiomaster TX16S roller wheel replacement (and speaker)
OpenTX / Radiomaster TX16s

Radiomaster TX16S roller wheel replacement (and speaker)

June 7, 2021June 7, 20210

I had an issue with roller wheel on my Radiomaster TX16s that it scrolls only one way (down) and sometimes few times up, but its really hard to use. Same …

INAV remapping RESOURCEs in 10 minutes (or add PINIO)
Feiyue FY-03 / INAV Betaflight / RC | FPV

INAV remapping RESOURCEs in 10 minutes (or add PINIO)

April 18, 2021April 18, 20213

I would like to use realPit for turning off my VTX on crawler if I’m driving LOS so save some battery and heatThere’s currently not used DAC pin on MatekF722 …

Insta360 GO 3D model
3D Print / RC | FPV

Insta360 GO 3D model

August 4, 2020August 4, 20200

I ordered another serious toy – really small and light camera (18g) for my small whoop, RC car and also XK A800 glider.I get it from aliexpress with combination of …

XK A800 – brushless motor update
3D Print / XK A800

XK A800 – brushless motor update

June 26, 2020June 26, 20203

As a fist step of rebuild my XK A800 from toy to serious GPS glider is replace brushed motor to brushless.I decide to go to small and light 1306 tinywhoop …

Enter to Glider world – my first plane XK A800
RC | FPV / XK A800

Enter to Glider world – my first plane XK A800

June 12, 2020June 12, 20200

I started with theoretical RC world maybe 20 years ago with planing of my fist Plane / Glider.It takes few years of study and I made a list of parts …

Scrapy Koko 120 – 2.5″ with 3″ props or “break me please”
3D Print / Laser cut / RC | FPV / Scrapy Koko 120

Scrapy Koko 120 – 2.5″ with 3″ props or “break me please”

May 4, 2020May 4, 20200

As I updated my 3″ Cloud 149 cinewhoop with new motors, ESC, FC and VTX i would like to reuse leftowers from that. Those “scrapy” parts was quite poor and …

Posts navigation

1 2 3 Next

Categories

  • 3D Print
  • arduino
  • Cloud 149
  • download
  • Feiyue FY-03
  • FLOWBOX
  • Gyroflow
  • INAV Betaflight
  • Laser cut
  • LiPo
  • MISC
  • OpenTX
  • Peugeot
  • QX95
  • Radiomaster TX16s
  • RC | FPV
  • Scrapy Koko 120
  • SYMA X5C
  • XK A800
  • ZMR250
WizzX © 2022 | feel free to share | Powered by WordPress and Bam.